Chevrolet Keyless Entry System & Remotes. All You Need to Know. How to Program a New Keyless Entry / Unlock Remote for All Chevrolet Models. Instructions, Cost, Procedures, Troubleshooting and More.
- This page is relevant for programming ALL GM models for this remote. (Chevy, Buick, Cadillac, Pontiac, Saturn, Oldsmobile and some of Isuzu keys)
Give Us a Call 24/7 For All Chevy Lost Car Keys Replacement & Ignition Problems!
Call Now: 800-223-1453 or Click to Get a New Key Online
In this article:
Introduction – What is Chevy keyless entry remote/ unlock remote
How to choose the right keyless entry remote or replacement remote for my Chevy model?
Can I install Chevrolet keyless entry myself?
How much does it cost to replace or install keyless entry for Chevy models?
Can I reset my Chevy keyless entry?
Introduction – What is Chevy keyless entry remote / Unlock remote in a car?
Chevrolet Keyless entry remote, also known as unlocking remote or unlock button, is simply a remote that allows you to lock and unlock your car with a remote, instead of the manual key. In addition, some remotes allow you to pop to the trunk and have a panic button.
Furthermore, newer Chevrolet models made after 2010, have this feature built in the key fob. Alternatively, you can buy a separate remote in addition to your key.
Most Chevrolet models, newer and older, have the function of installing and programming keyless entry remote.
Finally, there are a few remotes used by Chevrolet and therefore it is very important to choose the right that fits your model. Otherwise, it won’t be programmed correctly and won’t unlock and lock your car.
Here we will go over the different type of keyless entry remotes, will show you how to choose which remote you need for your specific Chevrolet model and how to program the keyless entry yourself, should you choose to do so, which will save you time and money.
The process is relatively simple and fast.
All you need to do is to follow the instructions below.
Few tips about Chevrolet keyless entry remote, before you start looking for one:
There are a few keyless entry remotes available for Chevrolet models. Each one fits different models and different years.
In addition, for a specific model, a single remote will work for a few years. For example, GM-568 keyless remote is compatible with Chevrolet Suburban for all years between 1996-2000 as well as for Chevy Malibu 1996-2000. Therefore, if you are not sure if your Malibu was made in 1996 or 1997, you can be sure it would work for you.
Furthermore, programming Chevy keyless remote sometimes require 2 remotes. Therefore, if you decide to buy it online, make sure you don’t need two of them.
As always, we recommend verifying your model year simply by checking the VIN number of the car. Not sure how to do that? Click here for instructions.
How to choose the right keyless entry remote or replacement remote for my Chevy model?
Choosing the right keyless entry is very important to avoid issues and hassle. As mentioned above, you need to make sure you get the right remote/part, otherwise, it won’t program and won’t function.
Therefore, we made it easy for you. You can simply choose your model & year, and click on the right remote below to see all relevant information. You can do that HERE.
Can I install Chevy keyless entry myself?
Most Chevy models come with a keyless entry system built in already. You do need, however, to program the remote for it to function. For older models, mostly 92 and older, you may need to go to a mechanic to actually install the system.
In addition, even if you have never had a remote keyless before, most chances you can still program it and it would work perfectly fine.
How much does it cost to replace or install keyless entry for Chevy models?
As mentioned above, the system itself is already built in for most Chevrolet models.
However, you will need to have the actual remote and to program it to unlock the car.
Let’s go over the approximate cost, process and how you can save money.
Remote keyless – Part only
Online: About $35 (Average price, if you buy it online yourself)
Automotive locksmith or dealer: About $60
Programming the remote:
You can do that yourself – usually within a few minutes.
Automotive locksmith or dealer: They usually charge about $60 for the process.
In conclusion, we would highly recommend getting the part online and program it yourself. It would save you about $80 and the process is fast and easy.
Give Us a Call 24/7 For All Chevy Lost Car Keys Replacement & Ignition Problems!
Call Now: 800-223-1453 or Click to Get a New Key Online
Chevrolet keyless entry – Can I reset it and how to do it?
The best way to reset your keyless entry is just to reprogram the remote again. In addition, you have to make sure the remote itself is functioning, as well as the battery. Once you reprogrammed the remote and you still have a problem, then you may have to go to a mechanic because most chances are the problem is with the vehicle.
How to program, reprogram or install Chevrolet keyless entry remote – A step by step guide before your start.
Chevrolet keyless entry remotes programming. Step by step guide. PLEASE READ CAREFULLY EACH STEP TO AVOID ANY ISSUES.
The process of programming a new Chevrolet keyless entry remote involve three phases.
- Choosing the right keyless for your specific model.
- Buying the remote
- Program the remote
Let’s go over each one of these steps.
First step – Choose the right keyless entry remote.
Choosing the right remote for your model is the most important thing. Some remotes look alike but have different frequencies they work on. Therefore, choosing the right is crucial.
The first thing you should do is verifying the year your car was made. The best way to do that is by the VIN number.
Second, now that we know the year and model, we can choose the right keyless remote.
Simply go to your Chevy model HERE and check the keyless entry remote for the relevant year.
Now that you know which remote you should use, let’s move on to the next step – buying the remote.
The second step – Buy the remote.
You have a few options for how to get the remote.
- Buy it online – Cheapest and most recommended way.
- Dealer
- Automotive Locksmith
It doesn’t really matter which option you choose if you get the right remote.
We already did the hard work for you by checking for each and every model which remote is the right one and therefore we would recommend getting it online yourself and save the money by going to the dealer or an automotive locksmith.
The third step – programming the remote.
Now you have the right remote, you just need to program it to your car.
Here are the programming instructions for all available Chevrolet keyless remotes.
*** We highly recommend reading the information above before programming your new remote!
Programming Instructions: Please choose the relevant method for your model.
(Method A)
First,
Make sure all doors are closed and sit in the driver seat. Now you should Locate the Data Link Port which It is located under the Driver’s side dash. There are no numbers there so keep in mind that number one is the one to the left. Identify ports eight (8) and four (4). The top row and contains ports one (1) through eight (8) and is wider than the bottom row. The bottom row contains ports nine (9) through sixteen (16) and is not relevant for programming.
Now, look at ports 8 & 4. There should be metal pins inside them.
Second,
Connect port eight (8) to port (4) with a suitable jumper wire. Any short piece of conductive wire will work (i.e. – a paper clip). DO THAT ONLY WHEN THE CAR IS OFF!
The jumper wire will stay connected throughout the programming procedure.
This step is basically to get the vehicle into programming mode. In case you did it right, the door locks will cycle. This way you know you can move on to the next step.
Third,
Now, on the first remote, press and hold both the LOCK and UNLOCK buttons together.
Wait between 10-20 seconds. In case you did it right, the door locks will cycle. This way you know you can move on to the next step.
Fourth,
You have one minute to complete this step.
Repeat the step above on all additional remotes, including working ones, to be programmed to the vehicle. Keep in mind, you have to do it even if you already have a working remote. Otherwise, it won’t work once you finish programming the new remotes.
Now, remove the jumper wire connected to the Data Link Port and test your new remotes. They should work.
Programming is now complete.
Need Help: Call Us Now 24/7 800-223-1453
Give Us a Call 24/7 For All Chevy Lost Car Keys Replacement & Ignition Problems!
Call Now: 800-223-1453 or Click to Get a New Key Online
Programming Instructions: (Method B)
There are two possible methods to program this remote. Choose the one that fits your vehicle.
First,
Make sure all doors are closed and sit in the driver seat. Insert a working key into the ignition and turn to “ON” position.
Second,
Press and hold the vehicle information button until PRESS TO RELEARN REMOTE KEY displays and then Press the set/reset button until REMOTE KEY LEARNING ACTIVE displays.
Third,
Now, press and hold the lock and unlock buttons on the keyless remote at the same time for approximately 15 seconds. A chime will sound indicating that the remote is programmed.
To program an additional remote/s, simply repeat this step again.
Fourth,
Once all new remotes are programmed, simply take the key out and test the new remotes. They should work now.
Programming is now complete.
Need Help: Call Us Now 24/7 800-223-1453
Use this Procedure for Vehicles without Drivers Information Center
First,
Make sure all doors are closed and sit in the driver seat. Insert a working key into the ignition and turn to “ON” position.
Second,
Press the trip odometer reset stem until RELEARN REMOTE KEY displays.
Third,
Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display indicating you can move on to the next step.
Fourth,
Press and hold the lock and unlock buttons on the first keyless remote at the same time for approximately 10-20 seconds. A chime will sound indicating that the remote is programmed.
If you wish to program additional remotes at this time repeat this step. This vehicle can have a maximum of eight remotes programmed.
Now simply turn key to “off” position, remove and test the new remotes.
Programming is complete.
Need Help: Call Us Now 24/7 800-223-1453
(Method C)
First,
Make sure all doors are closed and sit in the driver seat. Hold down the UNLOCK button on the driver’s door and continue holding until instructed to release.
Second,
Turn the ignition switch to “ON” position, then “OFF” then “ON” then “OFF”. You can now release the UNLOCK button.
In case you did it right, the door locks will cycle. This way you know you can move on to the next step.
Third,
Now, on the first remote, press and hold both the LOCK and UNLOCK buttons together until door locks and unlocks. It may take up to 30 seconds to happen.
Repeat this step for any additional remote you would like to program.
Fourth,
Turn the ignition switch to “ON” position to exit programming mode.
Programming is now complete. Your new remotes should work.
Need Help: Call Us Now 24/7 800-223-1453
(Method D)
- Before programming your new remote, make sure you have all the previous remotes as well. Once you program the new remote/s, all previous remotes won’t work.
First,
Make sure all doors are closed and sit in the driver seat. Insert the key into the ignition and turn to “ON” position. Then turn key to “OFF” position and take it out of the ignition.
Second,
Press and hold the driver side lock switch in “unlock” position. Then insert the key into the ignition and remove without turning the key.
Third,
Once again, insert the key into the ignition and remove without turning the key.
Then, insert the key again, and leave it in the ignition cylinder without turning it.
Fourth,
Release the “unlock” button. The vehicle should be now in programming mode. In case you did it right, three beeps will sound.
Now, press the “lock” and “unlock” button on the keyless entry to program it. The vehicle will beep twice to confirm successful programming. (It may take up to 15 seconds for the vehicle to beep – be patient)
Fifth,
Repeat the previous step to program all available new remotes. Once you are done, simply remove the key from the ignition to exit programming mode.
Need Help: Call Us Now 24/7 800-223-1453
(Method E)
- Before programming your new remote, make sure you have all the previous remotes as well. Once you program the new remote/s, all previous remotes won’t work.
First,
Make sure all doors are closed and sit in the driver seat. Remove the “BCM Program” fuse from the fuse panel which can be accessed by opening the front passenger door. Close all doors and liftgate.
Insert the key into the ignition and turn to “ACC” position and then turn key to “OFF” position and leave the key in the ignition.
Second,
Open and close any door. You should hear a chime will sound indicating programming mode.
Third,
For every remote you want to program, press and hold both “Lock” and “Unlock” buttons for 14 seconds. You should hear one sound after 7 seconds and an additional one after total 14 seconds meaning programming was successful.
Fourth,
Remove the key from the ignition.
Fifth,
Install the fuse back. Programming is complete. You can test your remotes now.
Need Help: Call Us Now 24/7 800-223-1453
(Method F)
- Before programming your new remote, make sure you have all the previous remotes as well. Once you program the new remote/s, all previous remotes won’t work.
First,
Make sure all doors are closed and sit in the driver seat. Locate the date link connector which is locations underneath the driver’s side dashboard. Connect cavity G and A using a fused jumper wire. The car should lock and unlock confirming programming mode.
Second,
Now, for each remote, you want to program, press any button 3 times. Locks should lock and then unlock confirming programming was successful.
Third,
Remote jumper wire. You can test your remotes now.
Need Help: Call Us Now 24/7 800-223-1453
Click to get specific information or order online:
GM Keyless Entry Remote 15913420
GM Keyless Entry Remote 15252034
GM Keyless Entry Remote 15732803
GM Keyless Entry Remote M3N32337100
GM Keyless Entry Remote ABO0103T
GM Keyless Entry Remote LHJ011
GM Keyless Entry Remote abo0204t
GM Keyless Entry Remote l2c0007t
GM Keyless Entry Remote ABO0302T/3T
GM Keyless Entry Remote KOBLEAR1XT